@article { author = {Fatemi, K and Rezvanianzadeh, M. R and Pashaee, H and Tarkash Esfahani, M}, title = {AUC Preparation from ADU Precipitated from Uranyl Fluoride Solution}, journal = {Journal of Nuclear Science and Technology (JONSAT)}, volume = {34}, number = {4}, pages = {64-76}, year = {2014}, publisher = {Nuclear Science and Technology Research Institute}, issn = {1735-1871}, eissn = {2676-5861}, doi = {}, abstract = {In this study, a simple method for the AUC powder preparation from uranyl fluoride solution, which is more effective for uranium recovery from AUC effluent is presented. At first, the uranium was precipitated in the form of ADU with more than 99.99 percent efficiency by ammonia solution. Then, through overflowing the solution, most of the fluoride ions were removed from the precipitated uranium. By adding ammonium carbonate solution to the ADU slurry, the AUC with stochiometry formula with high efficiency was prepared. The remained uranium in the AUC liquid waste was recovered by ADU precipitation in 99.99 percent. In this step, the uranium concentration in the final waste solution was decreased to less than 1ppm, where it is an important factor for enriched uranium. The ADU slurry was recycled to the next cycle of the AUC production. In this study, the NH4+ concentration, CO32-/UO22+ molar ratio and temperature effects were studied on the properties of the AUC powder and the precipitation efficiency. The results show that the NH4+ concentration is only effective on the fluoride separation and precipitation efficiency. The AUC precipitation efficiency depends on the uranium concentration in the ADU slurry. Also, the uranium recovery depends on the uranium concentration in the AUC waste. Decreasing the CO32-/UO22+ ratio to a minimum value caused the maximum particle size of the AUC crystals to be on an average value of 121 microns. The results of the XRD and SEM for the AUC powder are also presented.}, keywords = {Ammonium Uranyl Carbonate,Ammonium Diuranate,Uranyl Fluoride,Waste}, title_fa = {تولید آمونیم اورانیل کربنات از آمونیم دی‌اورانات تولید شده از محلول اورانیل فلورید}, abstract_fa = {روشی ساده برای تولید آمونیم اورانیل کربنات (AUC) از محلول اورانیل فلورید، اما مؤثر برای بازیابی اورانیم از پس­آب آمونیم اورانیل کربنات ارایه شد. در این روش، ابتدا اورانیم محلول به شکل آمونیم دی­اورانات (ADU) با بازده %99.99  با آمونیاک رسوب داده شد. سپس بخش اعظم یون‌­های فلوئور با سرریز کردن محلول از روی رسوب از اورانیم جدا شد. آن­گاه با افزودن محلول آمونیم کربنات به دوغاب این رسوب، ترکیب آمونیم اورانیل کربنات با بازده بالا تهیه شد. در ادامه اورانیم موجود در پس­آب آمونیم اورانیل کربنات نیز به شکل آمونیم دی­اورانات با بازده بالا بازیابی شد، به طوری­که غلظت اورانیم در پس­آب به زیر 1 میلی­گرم بر لیتر کاهش یافت. دوغاب آمونیم دی­اورانات حاصل در این مرحله به ظرف واکنش برگشت داده شد و چرخه­‌ی بعد برای تولید آمونیم اورانیل کربنات آغاز شد. در این بررسی اثر غلظت NH4+ ، نسبت مولی CO32-/UO22+ ، دما و غلظت اورانیم در دوغاب آمونیم دی­اورانات بر بازده رسوب­گیری و خواص پودر آمونیم اورانیل کربنات مطالعه شد. نتایج نشان­گر آن است که یون­‌های NH4+تنها بر میزان جداسازی یون­‌های فلوئور و بر بازده تأثیرگذار بود. در مقابل، اثر افزایش غلظت اورانیم در دوغاب آمونیم دی­اورانات بر بازده رسوب آمونیم اورانیل کربنات، و نیز اثر افزایش غلظت اورانیم در پس­آب آمونیم اورانیل کربنات بر بازیابی اورانیم از این پس­آب از مهم­ترین عامل­‌های تأثیرگذار تشخیص داده شدند. در نسبت مولی برابر 8 برای  CO32-/UO22+، افزایش اندازه­‌ی ذرات بلورهای آمونیم اورانیل کربنات با میانگین 121 میکرون بیشینه بود. الگوی پراش پرتو ایکس و ریزنگار الکترونی پودر آمونیم اورانیل کربنات تولید شده مشخصه‌­ی تشکیل ترکیب استوکیومتری آمونیم اورانیل کربنات و پدیده­‌ی بلورینگی بود.}, keywords_fa = {آمونیم اورانیل کربنات,آمونیم دی‌اورانات,اورانیل فلورید,پس‌آب}, url = {https://jonsat.nstri.ir/article_323.html}, eprint = {https://jonsat.nstri.ir/article_323_06ad0d747de51a454162444ec008a6af.pdf} }