@article { author = {Safavi, A and Abdi, M. R and Talebi, M and Esteki, M. H}, title = {The Model of Boiling Water Flow in the VVER-1000 Steam Generator}, journal = {Journal of Nuclear Science and Technology (JONSAT)}, volume = {34}, number = {3}, pages = {101-108}, year = {2013}, publisher = {Nuclear Science and Technology Research Institute}, issn = {1735-1871}, eissn = {2676-5861}, doi = {}, abstract = {2D and 3D numerical models of a steam generator for VVER-1000 type nuclear reactors used in the nuclear industry is presented. For the calculation Euler-Euler approach is applied for modeling the boiling heat transfer, boiling and recondensation. In the 3D model, the secondary side of the steam generator is simulated by the porosity model presented earlier by Stosic and Stevanovic. In the Porosity model, the tubes of the primary circuit are not described in detail, but they are modeled as sources of enthalpy and pressure loss. The physical models were implemented by user-defined programs in ANSYS-CFX12.1 computational fluid dynamics software. The results of the 3D thermal-hydraulic modeling of the steam generator in the Russian type VVER-1000 NPP for the full load operating condition are presented. The results clearly illustrate a void fraction distribution. Moreover, the role of submerged perforated sheet is investigated. The results are compared with a published paper in 1999 by Stevanovic. There is a good agreement between the introduced calculation. In addition, in the 2D model, the superficial velocity of water vapor is calculated as well.  }, keywords = {}, title_fa = {مدل‌سازی جریان آب جوش در مولد بخار VVER-1000}, abstract_fa = {مدل عددی دو بعدی و سه بعدی مولد بخار VVER-1000 ، که در صنعت هسته‌ای کشور از آن استفاده می­‌شود، در این مقاله ارایه شده است. برای مدل­سازی انتقال حرارت جوشان، جوشش و میعان از روش اویلر- اویلر و در مدل‌­سازی سه بعدی طرف ثانویه­‌ی مولد بخار از یک مدل فضای متخلخل پیش از این گزارش شده توسط استوسیک و استوانوویچ برای مولد بخار VVER-440 ، استفاده شده است. مدل فضای متخلخل به این معنی است که بسته لوله­‌های طرف ثانویه به طور جزیی و دقیق مدل­‌سازی نمی‌­شوند، بلکه به صورت منبع­‌های تکانه و انتالپی فرض می‌­شوند. مدل‌­های ساخته شده به کمک تابع­‌هایی که در ANSYS-CFX تعریف شده‌اند، بهبود یافته‌­اند. نتایج این مدل­‌سازی مربوط به حالتی است که مولد در حداکثر توان کار می­‌کند. نتایج به دست آمده، توزیع درصد حجمی بخار و نقش جداکننده­‌ی شناور را، که تنها در VVER-1000  وجود دارد، نشان می­‌دهد. برای راستی آزمایی نتایج، از نتایج آزمایشگاهی استوانوویچ (1997) استفاده شد. مقایسه بین نتایج به دست آمده از مدل عددی و نتایج تجربی تطابق قابل قبولی را نشان داد. در مدل دو بعدی، توزیع سرعت بخار در مکان­‌های مختلف به دست آمد.}, keywords_fa = {مولد بخار VVER-1000مدل عددی دو بعدی و سه بعدی,مدل فضای متخلخل}, url = {https://jonsat.nstri.ir/article_340.html}, eprint = {https://jonsat.nstri.ir/article_340_9b39c869e96bcf246ce9907a306f8459.pdf} }