مجله علوم، مهندسی و فناوری هسته‌ای

بررسی پارامترهای مؤثر در استخراج یون‌های کبالت از محیط غیرآبی با استفاده از استخراج‌کننده آلیکوات 336

نوع مقاله : مقاله پژوهشی

نویسندگان

فاطمه بدیهی 1
مهدی اسداله زاده 2
علی حقیقی اصل 1
رضوان ترکمان 2

1 دانشکده مهندسی شیمی، نفت، گاز، دانشگاه سمنان، صندوق پستی: 19111-35131، سمنان ـ ایران

2 پژوهشکده چرخه سوخت هسته‌ای، پژوهشگاه علوم و فنون هسته‌ای، سازمان انرژی اتمی ایران، صندوق پستی: 8486-11365، تهران- ایران

https://doi.org/10.24200/nst.2024.1611
چکیده
در این پژوهش، استخراج یون‌های کبالت از محیط غیرآبی با استفاده از استخراج‌کننده آلیکوات 336 انجام گردید. اثر پارامترهای مختلف بر فرایند استخراج غیرآبی شامل غلظت اتیلن گلیکول، غلظت استخراج‌کننده، غلظت هیدروکلریک اسید و غلظت یون‌های کبالت در محلول آبی با استفاده از روش طراحی آزمایش‌ مورد بررسی قرار گرفت. با توجه به مطلوبیت یک و درصد استخراج بیشینه کبالت، شرایط بهینه شامل درصد حجمی آلیکوات 336 (2/19 درصد)، غلظت کبالت (ppm 4/899)، درصد حجمی اتیلن گلیکول (3/65 درصد) و غلظت هیدروکلریک اسید (81/7 مولار) حاصل گردیدند. اعتبار داده­ها با حداقل خطا بین داده­های پیش‌بینی شده (82/94 درصد) و داده­های آزمایشگاهی (36/99 درصد) مشاهده گردید.

کلیدواژه‌ها

محیط غیرآبی
کبالت
استخراج‌کننده آلیکوات 336
اتیلن گلیکول
هیدروکلریک اسید
طراحی آزمایش

عنوان مقاله English

Investigation of effective parameters in the extraction of cobalt ions from non-aqueous medium using Aliquat336 extractant

نویسندگان English

F. Badihi 1
M. Asadollahzadeh 2
A. Hghighi-Asl 1
R. Torkaman 2
1 Faculty of Chemical, Petroleum and Gas Engineering, Semnan University, P.O.Box: 35131-19111, Semnan – Iran
2 Nuclear Fuel Cycle Research School, Nuclear Science and Technology Research Institute, AEOI, P.O.Box: 11365-8486, Tehran - Iran
چکیده English

Using Aliquat336 extractant, cobalt ions were extracted from a non-aqueous medium. The effect of different parameters on the non-aqueous extraction process including ethylene glycol concentration, extractant concentration, hydrochloric acid concentration, and cobalt ions concentration in aqueous solution was investigated using the experimental design approach. According to the desirability of one and the maximum extraction efficiency of cobalt ions, the optimal conditions include volume percentage of Aliquat336 (19.2%), cobalt concentration (899.4 ppm), volume percentage of ethylene glycol (65.3%) and hydrochloric acid concentration (7.81 M) were obtained. The validity of the data was observed with minimal error between the predicted data (94.82%) and the experimental data (99.36%).

کلیدواژه‌ها English

Non-aqueous medium
Cobalt
Aliquat336 extractant
Ethylene glycol
Hydrochloric acid
Experimental design
  1. Rumbu R. Extractive Metallurgy of Cobalt. CreateSpace Independent Publishing Platform. New York. 2018.

 

  1. Crundwell F.K, Preez N.B.d, Knights B.D.H. Production of cobalt from copper-cobalt ores on the African Copperbelt–An overview. Minerals Engineering. 2020:156:106450.

 

  1. Crundwell F, Moats M, Ramachandran V, Robinson T, Davenport W.G. Extractive Metallurgy of Nickel, Cobalt and Platinum Group Metals. Elsevier, New York. 2011.

 

  1. Wang S. Cobalt—Its recovery, recycling, and application. Jom. 2006;58:47-50.

 

  1. Zhijian C, Yunjiang S, Chunchua Z, Maoling L, Recent status on cobalt-60 gamma ray radiation sources production and its application in China. Radiation Physics and Chemistry. 1993;42:469-471.

 

  1. Mohanty A, Devi N. A Review on Green Method of Extraction and Recovery of Energy Critical Element Cobalt from Spent Lithium-Ion Batteries (LIBs). Mineral Processing and Extractive Metallurgy Review. 2023;44:52-63.

 

  1. Chandra M, Yu D, Tian Q, Guo X. Recovery of Cobalt from Secondary Resources: A Comprehensive Review. Mineral Processing and Extractive Metallurgy Review. 2022;43:679-700.

 

  1. Alvial-Hein G, Mahandra H, Ghahreman A. Separation and recovery of cobalt and nickel from end of life products via solvent extraction technique: A review. Journal of Cleaner Production. 2021;297:126592.

 

  1. Huang Y, Zhang Z, Cao Y, Han G, Peng W, Zhu X, Zhang T.-a, Dou Z. Overview of cobalt resources and comprehensive analysis of cobalt recovery from zinc plant purification residue- a review. Hydrometallurgy. 2020;193:105327.

 

  1. Amjad R.S, Asadollahzadeh M, Torkaman R, Torab-Mostaedi M. An efficiency strategy for cobalt recovery from simulated wastewater by biphasic system with polyethylene glycol and ammonium sulfate. Scientific Reports. 2022;12:17302.

 

  1. Amjad R.S, Asadollahzadeh M, Torkaman R, Torab-Mostaedi M. Optimizing the extraction of cobalt ions under response surface methodology and without organic solutions. Canadian Journal of Chemical Engineering. 2023;101:3532-3540.

 

  1. Asadollahzadeh M, Torkaman R, Torab-Mostaedi M, Saremi M. Experimental and modeling investigation of cobalt ion extraction in multistage extractor: Efficient evaluation of mass transfer coefficients using forward mixing approach. International Communications in Heat and Mass Transfer. 2021;125:105359.

 

  1. Maleki F, Gholami M, Torkaman R, Torab-Mostaedi M, Asadollahzadeh M. Multivariate optimization of removing of cobalt(II) with an efficient aminated-GMA polypropylene adsorbent by induced-grafted polymerization under simultaneous gamma-ray irradiation. Scientific Reports. 2021;11:18317.

 

  1. Maleki F, Gholami M, Torkaman R, Torab-Mostaedi M, Asadollahzadeh M. Cobalt(II) removal from aqueous solution by modified polymeric adsorbents prepared with induced-graft polymerization: Batch and continuous column study with analysis of breakthrough behaviors. Environmental Technology & Innovation. 2021;24:102054.

 

  1. Torkaman R, Asadollahzadeh M. Study and Investigation of Process Parameters for Solvent Extraction of Cobalt from Chloride Solution by Using Mixture of Compelxing Agents Cyanex272, TBP, TOPO. Journal of Iranian Chemical Engineering. 2020;19:30-42.

 

  1. Torkaman R, Asadollahzadeh M, Torab-Mostaedi M, Maragheh M.G. Reactive extraction of cobalt sulfate solution with D2EHPA/TBP extractants in the pilot plant Oldshue–Rushton column. Chemical Engineering Research and Design. 2017;120:58-68.

 

  1. Torkaman R, Asadollahzadeh M, Torab-Mostaedi M, Maragheh M.G. Recovery of cobalt from spent lithium ion batteries by using acidic and basic extractants in solvent extraction process. Separation and Purification Technology. 2017;186:318-325.

 

  1. Earl C, Shah I.H, Cook S, Cheeseman C.R. Environmental Sustainability and Supply Resilience of Cobalt Sustainability. 2022;14:4124.

 

  1. Moskalyk R.R, Alfantazi A.M. Review of present cobalt recovery practice. Mining, Metallurgy & Exploration. 2000;17:205-216.

 

  1. Nguyen V.T, Riaño S, Aktan E, Deferm C, Fransaer J, Binnemans K. Solvometallurgical Recovery of Platinum Group Metals from Spent Automotive Catalysts. ACS Sustainable Chemistry & Engineering. 2021;9:337–350.

 

  1. Li Z, Dewulf B, Binnemans K. Nonaqueous Solvent Extraction for Enhanced Metal Separations: Concept, Systems, and Mechanisms. Industrial & Engineering Chemistry Research. 2021;60:17285-17302.

 

  1. Binnemans K, Jones P.T. Solvometallurgy: An Emerging Branch of Extractive Metallurgy. Journal of Sustainable Metallurgy. 2017;3:570-600.

 

  1. Badihi F, Asl A.H, Asadollahzadeh M, Torkaman R. Applied novel functionality in separation procedure from leaching solution of zinc plant residue by using non-aqueous solvent extraction. Scientific Reports. 2023;13:1146.

 

  1. Orefice M, Audoor H, Li Z, Binnemans K. Solvometallurgical route for the recovery of Sm, Co, Cu and Fe from SmCo permanent magnets. Separation and Purification Technology. 2019;219:281-289.

 

  1. Batchu N.K, Li Z, Verbelen B, Binnemans K. Structural effects of neutral organophosphorus extractants on solvent extraction of rare-earth elements from aqueous and non-aqueous nitrate solutions. Separation and Purification Technology. 2021;255:117711.

 

  1. Brecht Dewulf, Batchu N.K, Binnemans K. Enhanced Separation of Neodymium and Dysprosium by Nonaqueous Solvent Extraction from a Polyethylene Glycol 200 Phase Using the Neutral Extractant Cyanex 923. ACS Sustainable Chemistry & Engineering. 2020;8:19032-19039.

 

  1. Rizk S.E, Gamal R, El-Hefny N.E. Insights into non-aqueous solvent extraction of gadolinium and neodymium from ethylene glycol solution using Cyanex 572. Separation and Purification Technology. 2021;275:119160.

 

  1. Batchu N.K, Hoogerstraete T.V, Banerjee D. Non-aqueous solvent extraction of rare-earth nitrates from ethylene glycol to n-dodecane by Cyanex 923. Separation and Purification Technology. 2017;174:544-553.

 

  1. Batchua N.K, Hoogerstraete T.V, Banerjeeb D, Binnemans K. Separation of rare-earth ions from ethylene glycol (+LiCl) solutions by non-aqueous solvent extraction with Cyanex 923. RSC Advances. 2017;7:45351-45362.

 

  1. Dewulf B, Riaño S, Binnemans K. Separation of heavy rare-earth elements by non-aqueous solvent extraction: Flowsheet development and mixer-settler tests. Separation and Purification Technology. 2022;290:120882.

 

  1. Batchu N.K, Dewulf B, Riaño S, Binnemans K. Development of a solvometallurgical process for the separation of yttrium and europium by Cyanex 923 from ethylene glycol solutions. Separation and Purification Technology. 2020;235:116193.

 

  1. Marczenko Z, Balcerzak M. Separation, Preconcentration and spectrophotometry in inorganic analysis. Elsevier, New York. 2000.

 

  1. Li Z, Li X, Raiguel S, Binnemans K. Separation of transition metals from rare earths by non-aqueous solvent extraction from ethylene glycol solutions using Aliquat 336. Separation and Purification Technology. 2018;201:318-326.

 

  1. Wang M, Zhang Y, Muhammed M. Critical evaluation of thermodynamics of complex formation of metal ions in aqueous solutions III. The system Cu(I,II)-Cl--e at 298.15 K. Hydrometallurgy. 1997;45:53-72.

 

  1. Rybka P, Regel-Rosocka M. Nickel(II) and Cobalt(II) Extraction from Chloride Solutions with Quaternary Phosphonium Salts. Separation Science and Technology. 2012;47:1296-1302.

 

  1. Blitz-Raith A.H, Paimin R, Cattrall R.W, Kolev S.D. Separation of cobalt (II) and nickel (II) by solid-phase extraction into Aliquat 336 chloride immobilized in poly(vinyl chloride). Talanta. 2007;71:419-423.

 

  1. Zahn M, Ohki Y, Fenneman D.B, Gripshover R.L, Gehman V.H. Dielectric properties of water and water/ethylene glycol mixtures for use in pulsed power system design. IEEE. 1986;74:1182-1221.

 

  1. Sato T, Shimomura T, Murakami S, Maeda T, Nakamura T. Liquid-liquid extraction of divalent manganese, cobalt, copper, zinc and cadmium from aqueous chloride solutions by tricaprylmethyl-ammonium chloride. Hydrometallurgy. 1984;12:245-254.

صفحه اصلی