نوع مقاله : مقاله پژوهشی
نویسندگان
1 پژوهشکدهی راکتور و ایمنی هستهای، پژوهشگاه علوم و فنون هستهای، صندوق پستی: 1339-14155، تهران ـ ایران
2 پژوهشکده کاربرد پرتوها، پژوهشگاه علوم و فنون هستهای، سازمان انرژی اتمی، صندوق پستی: 14155-1339، تهران- ایران
چکیده
در این مطالعه از دو روش پوششدهی نانوذرات دیاکسید سیلیکون (2SiO)، جوشش استخری و الکتروفورتیک، جهت افزایش شار حرارت بحرانی نوارهای استیل مورد استفاده قرار گرفته است. در هر یک از این دو روش، پوششدهی در مدت زمان 20، 40 و 60 دقیقه با ثابت نگه داشتن سایر پارامترها انجام شده و با بررسی تصاویر SEM و EDS گرفته شده، زاویه تماس اندازهگیری شده است. با استفاده از این دو روش، سطوح آبدوست و فوقآبدوست ایجاد شده، منحنی جوشش و شار حرارت بحرانی محاسبه شده و با روابط تجربی و تحلیلی موجود مقایسه گردید. نتایج نشان داد که زاویه تماس برای سطوح پوششدهی شده به روش جوشش استخری کمتر از روش الکتروفورتیک است و در نتیجه شار حرارت بحرانی به مقدار قابلتوجهی افزایش مییابد. همچنین مقایسه نتایج شار حرارتی بحرانی حاضر با نتایج تجربی که تابعی از خواص سطح میباشند، همخوانی بهتری را نشان داد.
کلیدواژهها
عنوان مقاله [English]
Effect of nano-particle coating techniques of SiO2 on improvement of Critical Heat Flux
نویسندگان [English]
- A. Rahimian 1
- H. Kazeminejad 2
- H. Khalafi 1
- A. Akhavan 2
- M. Mirvakili 1
1 Reactor and Nuclear Safety Research School, Nuclear Science and Technology Research Institute, P.O.Box: 14155-1339, Tehran – Iran
2 Radiation Application Research School, Nuclear Science and Technology Research Institute, AEOI, P.O.Box: 1339-14155, Tehran – Iran
چکیده [English]
In this study, two methods of nano-particle coating, by boiling and electrophoretic, have been used to investigate the effect of surface modification on the Critical Heat Flux of stainless steel plates. In each of these two methods, the coating was performed for 20, 40, and 60 minutes while other parameters remained constant. The SEM1 and EDS2 images were captured and then the contact angles were measured using the Stadler technique to study the effect of surface properties on Critical Heat Flux. Finally, the boiling curves of the hydrophilic and superhydrophilic surfaces were obtained and then the Critical Heat Flux (CHF) is determined. The CHF values were compared with the existing experimental data and empirical correlations. It was found that the CHF for nanoparticle coating by pool boiling, is significantly higher than those of electrophoretic coating. Also, a comparison of the present Critical Heat Flux results with those obtained by the empirical correlations that are a function of surface properties showed better agreement
کلیدواژهها [English]
- Pool boiling coating
- Electrophoretic coating
- Critical heat flux